Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

bootmod3 development team has worked tirelessly throughout the course of the past few months to deliver a new feature to its end users dubbed

bootmod3 CustomROM

CustomROM is a set of changes to the DME software which augment and enhance its functionality with features not provided from the factory.

...

bootmod3 Map Editor Release

bootmod3 CustomROM Features Overview

  • CustomROM Map Switching: Switch between up to 4 individual map slots On-The-Fly using a combination of steering wheel Cruise Control buttons

    • Press and HOLD RESUME buttonfor 3 seconds to activate MapSwitching mode, then use Cruise Control UP or DOWN buttons (1st position UP or DOWN) to toggle between slots

    • Alternate option to trigger map switching mode on B48/B58/S58 vehicles where Resume button does not work or is not present:

      • Press and HOLD Cruise Control DOWN button (2nd position DOWN)

  • CustomROM Flex Fuel: Dynamically adjust any of the Flex Fuel enabled Map Slots in their torque/load, ignition timing and fuel maps when tuning for alcohol based fuels.

    • Check Ethanol % content in dash on the RPM gauge by pressing the DOWN button (1st of the two DOWN position).

    • Example: 1000rpm = 10% ethanol, 5000rpm = 50% ethanol

  • CustomROM Rolling Anti-Lag: Build boost by using a combination of steering wheel Cruise Control buttons and pressing on the accelerator pedal for pre-configured insta-boost when roll racing

    • Press and hold the UP button (1st of the two UP positions for F series vehicles except B58, 2nd UP position on all others) and pressing the accelerator pedal to go WOT

    • Various tuneable settings and safeties available when custom tuning such as: Min Accel Pedal required, Max. Time in Antilag mode, Engine Speed, Min and Max Temperature thresholds for Oil, Exhaust Gas Temps and others in the bootmod3 Map Editor

  • CustomROM Live Adjust: When flashed on CustomROM various live adjustables are now available to help users adjust tuning parameters without re-flashing. Map Configuration screen so far has served the purpose of end-user configuration for any given map. Live Adjust screen takes Map Configuration a step further and applies changes to a running vehicle, without reflashing.

    • Adjust exhaust burble on the fly, no re-flashing

    • Ethanol Sensor Content % Override - Useful in cases where ethanol sensor may have become faulty. Without this convenient live adjustable the driver would be stuck with a car not starting on a high concentration of ethanol in the tank and a DME that doesn’t see ethanol content due to a faulty/disconnected Flex Fuel sensor.

  • 4800+ tables available in the new Map Editor

  • Advanced Logging Updates: Various new as well as custom RAM datalogging channels to assist in tune review and custom tuning including over new/custom 80+ RAM channels

    • New RAM channels are definable if/when required by requesting it from the Map Editor

  • Flash Protocol Updates:

    • Last Flash Indicator on My Maps listing - Now stored with map on DME, does not require internet/server sync

    • Flash Counter Reset when re-flashing back to stock/re-lock for all MEVD DMEs

    • HPFP off during flashing to save battery life

bootmod3 CustomROM - Map Switching - 4 Integrated Map Slots

In its OEM form, the factory DME supports changes to Torque Request and Burble via the Driver Mode Selection switches (e.g. Efficient, Sport, SportPlus).

...

Widget Connector
overlayyoutube
_templatecom/atlassian/confluence/extra/widgetconnector/templates/youtube.vm
width750px
urlhttps://www.youtube.com/watch?v=iGu85QHKG48
height400px

bootmod3 CustomROM Flex Fuel - Tuning for alcohol based fuels

Info

FLEX FUEL HARDWARE SETUP REQUIREMENTS
To allow for Flex Fuel tuning, an Ethanol (alcohol) fuel sensor and an Ethanol Content Analyzer (ECA) CANBus device need to be connected to the vehicle’s PT-CAN.

Overview of the how the sensor data travels looks as follows:
Continental Flex Fuel Sensor → CANBus Enabled ECA Board → CANBus (PT-CAN) → DME running bootmod3 CustomROM

Flex Fuel sensor can be installed on the feed line as the factory S55 fuel system is return-less. If using the feed line, it is strongly recommended to use a splitter in the line where the sensor is installed to avoid introducing any fuel flow restrictions at higher power levels with higher fuel volume demand.

...

Widget Connector
overlayyoutube
_templatecom/atlassian/confluence/extra/widgetconnector/templates/youtube.vm
width750px
urlhttps://www.youtube.com/watch?v=UnR4O0_yyPY
height400px

bootmod3 CustomROM AntiLag

When racing or trying to achieve best acceleration times, the spool of a turbo impacts initial acceleration of the vehicle. The larger the turbo the more LAG (delay) before the turbo spools up and boost hits.

...

AntiLag tuning on the bootmod3 CustomROM is highly customizable and can be calibrated to any given setup by bootmod3 custom tuners. boost/load/torque, ignition and fuel target tables along with many configurable safeties and activation thresholds are available via the bm3 bootmod3 Tuning Editor.

Anti-Lag Demo:

Widget Connector
overlayyoutube
_templatecom/atlassian/confluence/extra/widgetconnector/templates/youtube.vm
width750px
urlhttps://www.youtube.com/watch?v=-23MTGbwdmE
height400px

bootmod3 CustomROM LiveAdjust - Live Tuning Changes, no re-flashing

...

In the case of Ethanol Sensor or ECA board failure or disconnect, where users have a full tank of ethanol in the car, we’ve added the ability to override actual sensor value with a preset fixed ethanol sensor value so the car can be started and driven again. Some users may also override this value at important race events to avoid any chances of sensor cut-out/dying when racing when they’re sure of the ethanol content in the tank from the fill-up prior *** USE WITH CAUTION

LiveAdjust screen demonstrates some of the live changes we’re doing to actual calibration tables in the DME.

...

Below we share the currently available set of over 80 RAM channels configurable for logging. bootmod3 logging is UDS/Ethernet based and is implemented in a way that allows for higher data throughput unlike many other tools on the market today being able to do over 70 channels combined between DID and RAM at just over 20-22 samples per second.

bootmod3 New RAM Channels For Datalogging (only CustomROM):

...

bootmod3 Antilag Active

...

bootmod3 Flex Blend Factor (Fuel)

...

bootmod3 Flex Blend Factor (Ign.)

...

bootmod3 Flex Blend Factor (Trq.)

...

bootmod3 Flex Ethanol %

...

bootmod3 Flex Ethanol % (Sensor)

...

bootmod3 Flex Fuel Temp

...

bootmod3 Flex Sensor Fault

...

bootmod3 Fuel Corr. (Base)

...

bootmod3 Fuel Corr. (Final)

...

bootmod3 Fuel Corr. (Flex Adder)

...

bootmod3 Map Slot
bootmod3 Updated RAM Channels For Datalogging (all MEVD17.2 based vehicles, S55 specific list below):
(RAM) Boost Pressure (Target)
(RAM) Boost Setpoint
(RAM) Boost Setpoint (AppMode)
(RAM) Engine Speed
(RAM) Fuel Delivery Rate (lph)
(RAM) Fuel Inj. Corr.
(RAM) Fuel Inj. Timing (End)
(RAM) Fuel Inj. Timing (Start)
(RAM) Fuel Injection Angle 1
(RAM) Fuel Injection Angle 2
(RAM) Fuel Injection Angle 3
(RAM) Fuel Injection Angle 4
(RAM) Fuel Injection Angle 5
(RAM) Fuel Injection Angle 6
(RAM) Fuel Injection Duration (Corrected)
(RAM) Fuel Mass Rel. (Corr.) 1
(RAM) Fuel Mass Rel. (Corr.) 2
(RAM) Fuel Mass Rel. (Target)
(RAM) HPFP (Actual)
(RAM) HPFP (Target)
(RAM) HPFP Pressure Control Deviation
(RAM) HPFP Regulator (I-Gain)
(RAM) HPFP Regulator (P-Gain)
(RAM) HPFP Regulator Output
(RAM) Ignition Timing (Target)
(RAM) Ignition Timing Corr. (Total)
(RAM) Ignition Timing Corr. Cyl. 1
(RAM) Ignition Timing Corr. Cyl. 2
(RAM) Ignition Timing Corr. Cyl. 3
(RAM) Ignition Timing Corr. Cyl. 4
(RAM) Ignition Timing Corr. Cyl. 5
(RAM) Ignition Timing Corr. Cyl. 6
(RAM) Ignition Timing Mode (Spool)
(RAM) Lambda (Base) Bank 1
(RAM) Lambda (Base) Bank 2
(RAM) Lambda Bank 1
(RAM) Lambda Bank 2
(RAM) Lambda Labas Switch
(RAM) Lambda Level 1 Bank 1
(RAM) Lambda Level 1 Bank 2
(RAM) Lambda Level 2 Bank 1
(RAM) Lambda Level 2 Bank 2
(RAM) Lambda Main (Target)
(RAM) Lambda Status
(RAM) Load (Actual)
(RAM) Load (Limit)
(RAM) Load (Target)
(RAM) MAF After Corr. (Target)
(RAM) MAF HFM
(RAM) MAF Pre-Turbine (Actual)
(RAM) MAF Pre-Turbine (Target)
(RAM) MAF Turbine (Actual)
(RAM) MAF Turbine (After Temp Corr.)
(RAM) Rel. Fill (Actual)
(RAM) Rel. Fill (Target)
(RAM) Torque at Clutch (Actual)
(RAM) Torque at Clutch (Target)
(RAM) Torque at Clutch (Target) (Pre-DrivDynmcs)
(RAM) Torque Limit Active (Flag)
(RAM) Torque Max Request
(RAM) Turbine Distribution Factor (Turbine/Wastegate)
(RAM) Turbine Power (Actual)
(RAM) Turbine Power (Compressor Map)
(RAM) Turbine Power (D-Gain)
(RAM) Turbine Power (I-Gain) (AppMode)
(RAM) Turbine Power (P-Gain)
(RAM) Turbine Power Adder (P-Gain)
(RAM) WGDC (After Corr.)
(RAM) WGDC (Base)
(RAM) WGDC (D-Gain)
(RAM) WGDC (I-Gain)
(RAM) WGDC (P-Gain)

Filter by label (Content by label)
showLabelsfalse
max5
spacescom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@10032
showSpacefalse
sortmodified
typepage
reversetrue
labelscustomrom tuning custom bootmod3
cqllabel in ( "customrom" , "custom" , "bootmod3" , "tuning" ) and type = "page" and space = "BCS"
Page Properties
hiddentrue

Related issues